导致全自动铝条折弯机折弯尺寸不准确的原因如下

　　The reasons for the inaccurate bending dimensions of the fully automatic aluminum strip bending machine are as follows

　　一、检查铝条折弯机整体结构

　　1、 Check the overall structure of the aluminum strip bending machine

　　在开始调整之前，首先要检查铝条折弯机的整体结构是否稳定，有没有异响或者松动。如果出现问题，需要进行紧固或者更换。

　　Before starting the adjustment, the overall structure of the aluminum strip bending machine should be checked for stability, any abnormal noise or looseness. If there is a problem, it needs to be tightened or replaced.

　　二、调整上模和下模的距离

　　2、 Adjust the distance between the upper and lower molds

　　上模和下模的距离影响铝条折弯的角度和圆弧度。通过调整上模和下模的距离实现铝条折弯的角度和圆弧度。具体方法是使用量规测量，然后进行微调。

　　The distance between the upper and lower molds affects the angle and curvature of the aluminum strip bending. By adjusting the distance between the upper and lower molds, the angle and curvature of the aluminum strip bending can be achieved. The specific method is to use a gauge to measure and then make fine adjustments.

　　三、更换或修复弯曲模具

　　3、 Replace or repair bent molds

　　铝条折弯机的弯曲模具如果有损坏或者磨损，会导致铝条折弯的尺寸不准确。需要及时更换或者修复模具。

　　If the bending mold of the aluminum strip bending machine is damaged or worn, it will result in inaccurate dimensions of the aluminum strip bending. It is necessary to replace or repair the mold in a timely manner.

　　四、调整刀具高度

　　4、 Adjust the tool height

　　铝条折弯机的刀具决定了折弯机器的切割深度和角度。如果铝条折弯的尺寸不准确，可能是刀具高度设置不正确。需要根据铝条的厚度和折弯角度进行调整。

　　The cutting tool of the aluminum strip bending machine determines the cutting depth and angle of the bending machine. If the size of the bent aluminum strip is not accurate, it may be due to incorrect tool height settings. Adjustments need to be made based on the thickness and bending angle of the aluminum strip.

　　五、校准液压系统

　　5、 Calibrate hydraulic system

　　液压系统的调整对铝条折弯机的准确性有很大的影响。需要检查液压油的压力和流量是否正常，以及液压系统的管道是否有泄露等情况。根据具体情况进行维修和调整。

　　The adjustment of the hydraulic system has a significant impact on the accuracy of the aluminum bar bending machine. It is necessary to check whether the pressure and flow rate of the hydraulic oil are normal, as well as whether there are leaks in the pipelines of the hydraulic system. Repair and adjust according to specific circumstances.

　　六、经常维护铝条折弯机

　　6、 Regularly maintain the aluminum strip bending machine

　　经常维护铝条折弯机是确保铝条折弯机尺寸准确性的关键。保持机器的干净，定期更换润滑油，检查配件是否有磨损或者损坏等。

　　Regular maintenance of the aluminum strip bending machine is key to ensuring its dimensional accuracy. Keep the machine clean, regularly replace lubricating oil, and check for wear or damage to accessories.

　　总之，通过以上一系列方法，可以调整铝条折弯机尺寸准确性，提高工作效率，为生产带来更高的效益。

　　In summary, through the above series of methods, the size accuracy of the aluminum strip bending machine can be adjusted, work efficiency can be improved, and higher benefits can be brought to production.

　　第二种办法：

　　The second method:

　　1、上下模对刀中心的不同，会导致折弯尺寸误差，折弯前需要调整上下模对刀中心。

　　1. The difference in the center of alignment between the upper and lower molds can lead to bending size errors, and it is necessary to adjust the center of alignment between the upper and lower molds before bending.

　　2、后挡料块左右位置移动后，板料与下模的相对位置可能发生变化，从而影响折弯尺寸。折弯前，应重新测量后挡块的位置距离。

　　2. After the left and right positions of the rear block are moved, the relative position between the sheet metal and the lower mold may change, thereby affecting the bending size. Before bending, the position distance of the rear stopper should be remeasured.

　　3、工件与下模平行度不够，会造成弯曲回弹，影响弯曲角度。弯曲前应测量并调整平行度。

　　3. Insufficient parallelism between the workpiece and the lower mold can cause bending and rebound, affecting the bending angle. Before bending, the parallelism should be measured and adjusted.

　　4、当弯曲角度不足时，第二次弯曲也会受到影响，弯曲误差的积累会导致工件成形尺寸和角度误差的增大，因此确保单边弯曲精度尤为重要。

　　4. When the bending angle is insufficient, the second bending will also be affected, and the accumulation of bending errors will lead to an increase in the forming size and angle errors of the workpiece. Therefore, ensuring the accuracy of unilateral bending is particularly important.

　　本文由 全自动铝条折弯机   友情奉献.更多有关的知识请点击  /   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from the fully automatic aluminum strip bending machine For more related knowledge, please click / Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.