1.润滑两个电动机。丁基胶打胶机的主电动机和辅助电动机的入口均装有润滑器。
1. Lubricate both motors. Lubricators are installed at the inlet of main motor and auxiliary motor of butyl glue applicator.
当机油低于低端刻线时，应将机油杯取下并重新加注10号机油。 如果没有注油器，则在滴油或电动机严重缺油时，可以拆下主电动机进气管和电动机之间的带电连接，并应使用油枪补充油，并使用辅助电动机 可以旋开端盖螺母以加油。
When the oil is lower than the low-end notch, remove the oil cup and refill No. 10 oil. If there is no oiler, in case of oil dripping or serious oil shortage of the motor, the live connection between the air inlet pipe of the main motor and the motor can be removed, and the oil gun shall be used to replenish the oil, and the end cover nut can be loosened for refueling with the auxiliary motor.
2.丁基胶打胶机使用一段时间后，主泵，辅助泵和比例泵会从内部泄漏胶水，并流入油杯。 您可以清洁胶水并添加油。 用十字螺丝刀固定住主泵，将两个泵油碗的下端的圆孔顺时针拧紧。 配套的油杯可用扳手拧紧。
2. After the butyl glue applicator is used for a period of time, the main pump, auxiliary pump and proportional pump will leak glue from the inside and flow into the oil cup. You can clean the glue and add oil. Fix the main pump with a cross screwdriver and tighten the round holes at the lower ends of the two pump oil bowls clockwise. The matched oil cup can be tightened with a wrench.

3.用油枪将安全阀注满安全阀的小孔，以防生锈。
3. Fill the small hole of the safety valve with an oil gun to prevent rust.
4. Y型过滤器位于辅助泵的出口。 清洁时，拧开端盖，将其浸入煤油中，然后用牙刷清洁。 安装时，将网罩放到端盖中并拧到底，然后用扳手拧紧。 用一套胶水清洗一次，如果没有杂质，用两套胶水清洗，控制灵活。
4. The Y-type filter is located at the outlet of the auxiliary pump. When cleaning, unscrew the end cap, immerse it in kerosene, and then clean it with a toothbrush. During installation, put the net cover into the end cover and screw it to the end, and then tighten it with a wrench. Clean once with one set of glue. If there are no impurities, clean with two sets of glue for flexible control.
5.大型过滤器的位置在高压仪表B台的右下角，拧下回油阀下方的软管，拧下过滤器，取出网和芯，弹簧，取出，用刷子清洗， 并用凸块上的芯覆盖弹簧的小孔。 向后旋转，然后将其拧紧在丁基胶打胶机上。
5. The large filter is located at the lower right corner of the high-pressure instrument B. unscrew the hose under the oil return valve, unscrew the filter, take out the net and core, take out the spring, clean it with a brush, and cover the small hole of the spring with the core on the boss. Rotate it backward and tighten it on the butyl glue applicator.
3-5组洗一次。 如果没有杂质，则可以灵活控制。
Wash once for 3-5 groups. If there are no impurities, it can be flexibly controlled.
以上就是双组份打胶机给大家的精彩内容，更多的精彩内容请点击：http://www.sandyklempnerathome.com我们后续会有更多的精彩内容等您查看.
These are the highlights of the two-component gluing machine. For more highlights, please click: http://www.sandyklempnerathome.com We will have more wonderful content for you to check later